ZyPer4K Firmware Updates

Please contact support for the latest Firmware update +1 (877) 493-3833 or send email to info@zeevee.com.

ZYPER4K HDMI 2.0 FIRMWARE - REVISION 3.5.2, RELEASED SEPTEMBER 26, 2018

Supported platforms: ZyPer4K HDMI2.0 encoders and decoders. NOTE: This update is for the devices with white metal casing only, not black.

Release notes:

  • CEC control - on/off command and hex codes are supported
  • New firmware file format - *.apz file.
  • The new *.apz file format requires the ZyPer Management Platform to be running version 1.8 or later.

IMPORTANT NOTE: This firmware release is not backwards compatible with older firmware for some resolutions.  To ensure full compatibility, please update all ZyPer4K HDMI2.0 devices to firmware version 3.4.0 or later when using the following resolutions:

  • 4K60 8-bit RGB and YCbCr 4:4:4
  • 4K60 10-bit YCbCr 4:2:2
  • 4K60 12-bit YCbCr 4:2:2
  • 4K60 12-bit YCbCr 4:2:2
  • 4K30 12-bit RGB and YCbCr 4:4:4

Version 1.8 of the ZyPer Management Platform is a major release with significant changes to the operating environment. For full details on all the changes, please review the ZyPer Management Platform Release Notes document before proceeding with the update.

ZYPER4K HDMI 2.0 FIRMWARE - REVISION 3.4.0, RELEASED MARCH 21, 2018

Supported platforms: ZyPer4K HDMI2.0 encoders and decoders. NOTE: This update is for the devices with white metal casing only, not black.

Release notes:

  • Change to TTL value from 1 to 32 for video and audio streams
  • Corrected an issue where scaled stream (used in Multiview) would not be set if the source was not detected.

IMPORTANT NOTE: This firmware release is not backwards compatible with older firmware for some resolutions.  To ensure full compatibility, please update all ZyPer4K HDMI2.0 devices to firmware version 3.4.0 when using the following resolutions:

  • 4K60 8-bit RGB and YCbCr 4:4:4
  • 4K60 10-bit YCbCr 4:2:2
  • 4K60 12-bit YCbCr 4:2:2
  • 4K60 12-bit YCbCr 4:2:2
  • 4K30 12-bit RGB and YCbCr 4:4:4

Please download the latest release notes for more information.

ZYPER4K HDMI 2.0 FIRMWARE - REVISION 3.3.2, RELEASED DECEMBER 11, 2017

Supported platforms: ZyPer4K HDMI2.0 encoders and decoders. NOTE: This update is for the devices with white metal casing only, not black.

Release Notes:

  • Support for Multiview to 1080p displays.
  • Support genlocked scaling to 1080p displays.
  • Support for flash LEDs command.
  • Support for factory defaults command.

ZYPER4K HDMI 2.0 FIRMWARE - REVISION 3.2.2, RELEASED MAY 22, 2017

Supported platforms: ZyPer4K HDMI2.0 encoders and decoders. NOTE: This update is for the devices with white metal casing only, not black.

Release Notes:

  • This update will automatically enable Auto-EDID which is required for Multiview
  • Added support for additional 4K60Hz input formats, output for these formats will be limited to 8-bit RGB
    • Added formats include:
    • 4K60Hz 8-bit 4:2:0
    • 4K60Hz 10-bit 4:2:0 (HDR)
    • 4K60 10-bit 4:2:2
  • Converts YUV 4:2:2 and YUV 4:2:0 source signals to RGB to make these sources available for all processing modes.

ZYPER4K FIRMWARE - REVISION 2.11.5, RELEASED FEBRUARY 9, 2017

Supported platforms: All current ZyPer4K encoders and decoders. NOTE: This update is for the devices with black metal casing not white.

Release Notes: Corrects a source address issue which causes audio packets to be dropped in switches that implement a “reverse path forwarding check”. Previous issue where a large audio delay was seen on video joins has been corrected.

This firmware update requires the ZyPer Management Platform to be running Release 1.4 or greater. 

ZYPER4K FIRMWARE - REVISION 2.10.5, RELEASED SEPTEMBER 19, 2016

Supported platforms: All current ZyPer4K encoders and decoders

Release Notes: Both 1080i 60Hz and 50Hz resolutions are now supported in Fast-switch mode. Previous firmware versions only supported 1080i in Genlocked mode. Video wall mode still only supports progressive resolutions · Support for Pronto formatted IR codes. A Pronto formatted string may now be injected to an endpoint via the ZyPerMP, and that IR code will be transmitted out the IR port.

WHITEPAPER: ZeeVee Security Features and Best Practices

Contact Support

  • This field is for validation purposes and should be left unchanged.